Particles size and shape analysis with image analyzer

The following analyses are included in this nanoparticle analysis package, intended to characterize nanoforms according to the REACH Regulation. Particle size distribution and aspect ratios by SEM-EDX Preparation with isopropanol, Sample dispersion on a slide, with centrifugation, SEM analysis and particle count by image analysis, Nanoparticle detection and classification according to the 2022 EC recommendation on the definition of nanomaterial, Reporting of PSD parameters for ~300 particles, including the following: PSD diagram, accumulated and individual., Feret min (min, d10, d25, d50, d75, d90, d95, max), Feret max (min, d10, d25, d50, d75, d90, d95, max), Equivalent circular diameter (min, d10, d25, d50, d75, d90, d95, max), Aspect ratio (calculated based on individual Feret min and Feret max measurements), Number based nano-fraction (%).. Crystal phase analysis by XRD/Rietveld method Sample preparation: drying, grinding, X-ray preparation, XRD analysis over an angular range extending from 10° to 90°, Identification of the crystalline phases present in the sample, Semi-quantitative analysis of phase distribution, using the Rietveld method, Interpretation of diffractograms. Chemical composition/purity by ICP-AES and CHNS analysis ICP-AES quantification of inorganic and metallic elements: Ag, Al, As, B, Ba, Be, Bi, Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Mo, Na, Ni, P, Pb, S, Se, Sb, Si, Sn, Sr, V, Zn, Ti, and Tl, Determination of C, H, N, and S with an elemental analyzer. Volume-specific surface area (VSSA) and VSSA diameter calculations (optional) BET specific surface area measurement of powder by nitrogen adsorption, True (skeletal) density measurement by He pycnometry, excluding intergranular and intragranular porosity, Both analyses include sample preparation. You can request a quote for the analysis using the form below. Please note that the OECD 125 guideline does not apply to this analysis.

Particle size distribution (PSD) is determined from transmission electron microscopy (TEM) images. The method is most suitable for small particles of 50 nm or smaller. Depending on particle shapes, the method includes calculating the diameters or lengths and widths of particles. In addition to size, TEM provides qualitative information about the surface morphology of the particles. TEM is a good option for irregularly shaped and non-spherical particles such as fibers, rods, and crystals that cannot be characterized meaningfully with traditional methods, including laser diffraction (LD) and dynamic light scattering (DLS). As a result of the analysis, TEM images and the determined particle size distribution for diameter (or length and width) are delivered. Dry samples are suitable for TEM as is. If the particles are wet or dispersed in a solvent, the sample may be dried with a suitable sample preparation method before imaging.

Determination of inhalable and respirable dust fractions present in indoor air. The aerodynamic diameters of the inhalable and respirable dust particles are < 100 µm and < 4 µm, respectively. The price includes a sample collector and a sample pump, which are delivered to the customer for sampling. Results are reported as mg/m³. According to the Finnish Ministry of Social Affairs and Health's decree on Hazardous Concentrations (538/2018), the normative threshold value for inhalable dust is 10 mg/m3 on an eight-hour average concentration.

Imaging of the sample using scanning electron microscopy (SEM). Typically, several images are taken with varying magnifications to get a good overview of the sample. Non-conductive samples can be prepared with a metallic coating to allow imaging. For cross-section measurement, additional preparation might be needed: FIB, BIB or freeze fracturing. If compositional analysis is also needed, please see the SEM-EDX measurement.

Imaging of the sample using a scanning electron microscope (SEM) with energy-dispersive X-ray spectroscopy (EDX or EDS). Typically, several images are taken with varying magnifications to get a good overview of the sample. An EDX mapping, line scan, or point measurement is collected to measure the sample composition (elemental at.% or wt.%). Non-conductive samples can be prepared with a metallic coating. For cross-section measurement, additional preparation might be needed: FIB, BIB, or freeze fracturing.

During this analysis, the surface of a smooth and hard sample is imaged with an atomic force microscope (AFM). Topological images are typically provided from three locations around the sample. The measurement area is 5 x 5 micrometers, if not otherwise agreed. Measurements are typically done using the following instrument: Bruker Dimension Icon.

Analysis of the specific surface area of porous, solid materials according to the BET (Brunauer–Emmett–Teller) theory. Analysis can be performed with N2 or Kr gases, depending on the expected surface area of the material. BET curve and the specific surface area (in m2/g) are reported. The required sample amount depends on the expected surface area. As a rule of thumb, at least 5 m2 of surface area should be available for measurement. The following gas adsorption devices are used for this measurement: Micromeritics Gemini VII 2390, Micromeritics ASAP 2020, Micromeritics TriStar II 3020, Anton Paar Nova 800.

Determination of particle size distribution (PSD) by Laser Diffraction (LD). Analysis can be performed on dispersions or solids that can be dispersed in water or organic solvents. The method can analyze particle sizes from 0.010 µm to 2000 µm. The test report will include a particle size distribution graph, values for volumetric mean = D[4,3], and the following percent finers (percent finers represent the amount of the material from the sample that is smaller than a certain size): Dv(10) / D(v,0.1) / 10 % , Dv(25) / D(v,0.25) / 25 % , Dv(50) / D(v,0.5) / 50 % = median, Dv(75) / D(v,0.75) / 75 % , Dv(90) / D(v,0.9) / 90 %.

Particle size distribution (PSD) is determined from scanning electron microscope (SEM) images of around 150 particles. Depending on the particle shapes, the method includes calculations on the diameters or lengths and widths of the particles. In addition to size, SEM provides qualitative information about surface morphology. SEM is a good option for irregularly shaped and non-spherical particles such as fibers, rods, and crystals that cannot be characterized meaningfully with traditional methods, including laser diffraction (LD) and dynamic light scattering (DLS). As a result of the analysis, SEM images and the determined particle size distribution for diameter (or one Feret dimension) are delivered. Samples must be completely dry for SEM. If the particles are wet or dispersed in a solvent, the sample may be dried with a suitable sample preparation method before imaging. Ask the method expert for more information and a price for analyzing your samples.

Measurement to determine the powder flowability index according to the ASTM D6393 standard for bulk solids characterization. The analysis includes the measurement and calculation of the following parameters: Angle of repose, Aerated bulk density, Packed bulk density, Compressibility, Angle of spatula, Cohesiveness.