Water vapor transmission rate (WVTR) of ultra-high barrier films and sheetings

This test is designed to measure the oxygen transmission rate of finished packages, including cups, bottles, trays, and containers. Two replica measurements are included in the displayed price. Temperature can be adjusted from 15 to 55 °C, and relative humidity can be either 0% or between 5 and 90% RH. This test is not suitable for films. Please see the oxygen transmission rate (OTR) of films and sheeting if you need testing for film samples. Please specify the sample dimensions and testing conditions upon ordering.

Determination of the oxygen transmission rate of plastic films and sheet-like materials. The test is performed on two parallel samples simultaneously. Measurement conditions (temperature and relative humidity) can be chosen according to the intended use of the material. Oxygen permeability is typically measured at 23 °C and 0% relative humidity as per standard ASTM D3985. In moist conditions, for example at 38 °C and 90% relative humidity, standard ASTM F1927 is used. Please disclose the desired temperature (from 15 °C to 50 °C) and relative humidity (either 0% or 10% to 90%) upon requesting an offer. This measurement is suitable for materials with OTR values between 0.01 and 5000 cm3/(m2 * day).

This measurement determines the transmission rate of carbon dioxide (CO2) through a single or multi-layered plastic film or sheeting with an infrared detector. The measurement is performed with two parallel specimens. The testing temperature is typically 23°C, and the relative humidity is 0%.

Determination of the water vapor transmission rate (WVTR) according to the ASTM F1249 standard. WVTR describes the amount of water vapor that passes through a material over a set period. It is an important quality indicator in food and cosmetics packaging, as an effective moisture barrier is critical to keeping products fresh and preventing spoilage. In this WVTR test, two samples per material are measured simultaneously to ensure the reliability of the measurement. The results are expressed as g/m²/day. Please disclose the desired temperature (from 15 to 50°C) and the desired relative humidity (from 35% to 90%) when placing the order. This measurement is applicable for plastic films and sheeting materials with WVTR values between 0.005 and 2000 g/m²/day. If you wish to test finished packaging instead, check out the WVTR measurement for packages.

X-Ray Reflectometry (XRR) analysis is used to measure the density (g/cm3), thickness (nm), and roughness (nm) of thin films. The method is applicable to the characterization of single- or multilayered thin films, as it provides information on the thickness and density of individual layers of the sample material as well as the roughness of the interphases. Greatest accuracy for XRR thickness measurements is generally achieved for samples containing 1-200 nm thick surface layers with under 5 nm RMS roughness. Thicker films and coatings with rougher surfaces can also be characterized, but the accuracy of thickness determination decreases as the thickness and roughness of the film or film stack increase. >150 mm wafers are typically cut to fit the sample holder. Please let us know if you need testing for larger wafers that cannot be cut into pieces. The available temperature range for XRR measurements is 25-1100 °C, and crystallinity can be studied as a function of temperature. The measurements can be performed under a normal atmosphere, inert gas, or vacuum. Measurements are typically performed using one of the following instruments: Rigaku SmartLab, Panalytical X'Pert Pro MRD, Bruker D8 Discover. Please let us know if you have a preference for a specific instrument.

Phthalates are a group of chemicals widely used as plasticizers, which make plastics more flexible and durable. They have also been used as additives in products such as cosmetics and personal care items. Several phthalates have been identified as endocrine-disrupting agents or as chemicals toxic to reproduction. Exposure to phthalates can occur through: Oral exposure Food: Exposure occurs via migration from food packaging., Children's toys: Children often put toys in their mouths.., Inhalation: Breathing in dust from vinyl flooring or fragrances (like perfumes) can cause exposure to phthalates via inhalation., Skin contact: Phthalates present in cosmetics, lotions, and soaps can be absorbed through the skin.. For other listed matrices apart from cosmetics, the analysis package covers the following substances included in the REACH Authorization List: Substance Abbreviation CAS number Diisobutyl phthalate DIBP 84-69-5 Dibutyl phthalate DBP 84-74-2 Benzyl butyl phthalate BBP 85-68-7 Bis(2-ethylhexyl) phthalate DEHP 117-81-7 Di(n-octyl) phthalate DNOP 117-84-0 Diisononyl phthalate DINP 68515-48-0 Diisodecyl phthalate DIDP 26761-40-0 Products that contain restricted phthalates in concentrations higher than 0.1% may be removed from the market. The analysis package for cosmetic products contains the following phthalates: Substance Abbreviation CAS number Bis(2-ethylhexyl) phthalate DEHP 117-81-7 Benzyl butyl phthalate BBP 85-68-7 Dibutyl phthalate DBP 84-74-2 Diisononyl phthalate DINP 68515-48-0 Di(n-octyl) phthalate DNOP 117-84-0 Diisodecyl phthalate DIDP 26761-40-0 All the above-mentioned substances are prohibited in cosmetic products (Annex II of Regulation (EC) No 1223/2009).

Analysis for quantifying dioxins and furans (PCDD/F) in various packaging materials (e.g. food and cosmetics packaging) and their raw materials, including plastics, paper, and rubber. Dioxins and furans are a family of chlorine-containing chemicals considered bioaccumulating, persistent organic pollutants (POPs) that can be toxic even at low doses. While regulatory limits apply mainly to food and feed, packaging materials can be a source of indirect exposure to dioxins and furans. Recycled materials tend to pose relatively high risks, depending on the quality of the raw material and the effectiveness of the decontamination process. The following substances are included in the analysis: Dibenzo-p-dioxins (PCDDs) Polychlorinated dibenzofurans (PCDFs) 2,3,7,8-TCDD. 2,3,7,8-TCDF. 1,2,3,7,8-PeCDD. 1,2,3,7,8-PeCDF. 1,2,3,4,7,8-HxCDD. 2,3,4,7,8-PeCDF. 1,2,3,6,7,8-HxCDD. 1,2,3,4,7,8-HxCDF. 1,2,3,7,8,9-HxCDD. 1,2,3,6,7,8-HxCDF. 1,2,3,4,6,7,8-HpCDD. 1,2,3,7,8,9-HxCDF. OCDD. 2,3,4,6,7,8-HxCDF. 1,2,3,4,6,7,8-HpCDF. 1,2,3,4,7,8,9-HpCDF. OCDF. Testing is often performed for the following reasons: Analyzing recycled PE, PP, and LDPE intended for cosmetics packaging according to CosPaTox guidelines., Analyzing paper and board bleached with elementary chlorine according to the requirements of TemaNord 2008:515 guidelines..

The new EU Packaging and Packaging Waste Regulation (PPWR) introduces additional requirements for the chemical safety of food packaging. This analysis package includes the following analyses required to demonstrate compliance: Total fluorine (TF), Heavy metals (Pb, Cd, Hg, and Cr), Further targeted PFAS analyses are available if required/requested.. The displayed typical price applies to TF analysis and heavy metal determination, which are sufficient for most materials. According to a recently published Commission guidance document, further PFAS testing is not required if TF content is less than 50 ppm. Please describe the composition of the packaging material when requesting an offer (materials with metal components may require the testing procedure to be modified). Please also let us know how many materials you need tested, as we are happy to offer discounted pricing for large batches.

The molar mass distribution of biomass samples soluble in pure water or organic solvents (DMF, DMSO, and THF) is measured using size exclusion chromatography with a refractive index detector (SEC-RID). The system is calibrated with polystyrene and dextran standards. A Pullulan standard is also available upon request. In the case of lignin samples, molar mass distribution is analyzed using SEC coupled with an ultraviolet detector at 256 nm wavelength. The lignin is dissolved in a suitable solvent before analysis, and the SEC system is calibrated with a polystyrene sulfonate standard. A borate buffer is used to set the pH for the eluent. The weight-average molecular weight (Mw) and number-average molecular weight (Mn) are reported. For absolute molecular weight, a GPC system coupled with a multi-angle light scattering (MALS) detector can be used. The mobile phase for this system is THF. An additional cost applies to this method.

Determination of the surface-drying characteristics of paints, varnishes, and related coating materials that dry by air action or chemical reaction, according to ISO 9117-3. The method does not apply to stoving products. The test uses ballotini glass beads applied to the coating surface to assess the surface-drying state. It can be performed in two ways: as a pass/fail test determining whether the surface-dry state has been reached after a specified time, or by repeated assessment at defined intervals to establish the surface-drying time. Results are reported as the surface-drying state at the specified time (go/no go) or as the time required to reach the surface-dry state. Measurlabs can also offer the following alternative drying tests from the ISO 9117 series: through-dry state and through-dry time (ISO 9117-1), pressure test for stackability (ISO 9117-2), mechanical recorder test (ISO 9117-4), modified Bandow-Wolff test (ISO 9117-5), and print-free test (ISO 9117-6). Please ask our experts for more information and a quote.