Polycyclic aromatic hydrocarbons (PAH) in water

This metal screening analysis includes the semi-quantitative determination of 70 elements. The method can be used, for example, to determine the background concentrations of metals in environmental samples or to study the elemental distribution of unknown samples. Screening is also often performed to assess which metals should be analyzed by a quantitative method. The measurement is performed using a high-resolution ICP-MS technique (ICP-SFMS), which can identify very low elemental concentrations. A semi-quantitative determination of the following elements is included: Ag, Al, As, Au, B, Ba, Be, Bi, Br, Ca, Cd, Ce, Co, Cr, Cs, Cu, Dy, Er, Eu, Fe, Ga, Gd, Ge, Hf, Hg, Ho, I, Ir, K, La, Lu, Mg, Mn, Mo, Na, Nb, Nd, Ni, Os, P, Pb, Pd, Pr, Pt, Rb, Re, Rh, Ru, S, Sb, Sc, Se, Si, Sm, Sn, Sr, Ta, Tb, Te, Th, Ti, Tl, Tm, U, V, W, Y, Yb, Zn and Zr. However, please note that some elements may not be determinable due to matrix interference. During this semi-quantitative analysis, the instrument is calibrated for about 30 elements and the rest of the analytes are quantified using sensitivity factors for calibrated elements with similar mass and first ionization potential considering isotope abundances. Quantitative analysis is also available at an additional price. During this analysis, all elements are calibrated (excluding halogens and Os). Please ask for an offer for this service.

Determination of carbon, hydrogen, nitrogen, sulfur, and oxygen content of an organic sample. CHNS analysis (”LECO analysis”) is performed using a flash combustion method, where the sample is combusted under 25 kPa of O2 at an elevated temperature (1000 °C), followed by gas chromatography separation and detection using a thermal conductivity detector. Oxygen is analyzed by reduction on granulated carbon at 1480 °C, utilizing high-temperature thermal decomposition and conversion of oxygen into carbon monoxide before gas chromatography separation and detection with a thermal conductivity detector. The sample can be either solid or liquid, but water in the sample affects the results. In the case of aqueous samples, it is possible to dry the sample before analysis. The displayed price by includes the full CHNOS package with two parallel measurements and applies to conventional organic samples. The results are reported as wt-% of the initial sample. The ash, drying and dry loss measurements will increase the minimum required sample material need to 300 mg. The analysis gives the total carbon, hydrogen, nitrogen, sulfur, and oxygen content of the material, but it does not identify any chemical structures. The measurement can be combined with other methods, such as GC-MS, 1H, and 13C NMR, to perform substance structure identification. Analysis can be split into the following packages: CHN, O, and S.

Analysis of gaseous samples using Raman spectroscopy.

Pyrolysis gas chromatography-mass spectrometry (py-GC-MS) analysis to determine the identity of an unknown polymer sample. During the measurement, the sample is instantaneously heated in an inert atmosphere or vacuum. This causes the sample to decompose into smaller molecular fragments which are then analyzed with GC-MS. Different types of polymers can be identified by their unique decomposition products. This includes, but is not limited to: PE, PP, PS, ABS, PMMA, PET, PC, PVC, polyamides, natural & synthetic rubbers, and more. The price includes the basic preparation and analysis of the sample. More extensive sample preparation is subject to additional costs.

Determination of selected volatile organic compounds (VOC) in water using the GC-MS and GC-FID techniques. Analysis can be conducted according to the following standard methods: EPA 624, EPA 5021A, EPA 8260, EPA 8015, EN ISO 10301, ISO 11423-1, and EN ISO 15680 The results of the analysis are reported in µg/L. Analysis includes the following analytes: Analyte: Reporting limits: chloromethane 1 µg/l bromomethane 1 µg/l dichloromethane 0.1 µg/l dibromimetaani 1 µg/l bromochloromethane 2 µg/l trichloromethane (chloroform) 0.1 µg/l tribromomethane (bromoform) 0.2 µg/l bromodichloromethane 0.1 µg/l dibromochloromethane 0.1 µg/l sum 4 trihalometanit 0.5 µg/l tetrachloromethane 0.1 µg/l trichlorofluoromethane 1 µg/l dichlorodifluoromethane 1 µg/l monochloroethane 1 µg/l 1,1-dichloroethane 0.1 µg/l 1,2-dichloroethane 0.1 µg/l 1,2-dibromietaani 0.5 µg/l 1,1,1-trichloroethane 0.1 µg/l 1,1,2-trichloroethane 0.1 µg/l 1,1,1,2-tetrachloroethane 0.1 µg/l 1,1,2,2-tetrachloroethane 1 µg/l vinyl chloride 0.1 µg/l 1,1-dichloroethene 0.1 µg/l cis-1,2-dichloroethene 0.1 µg/l trans-1,2-dichloroethene 0.1 µg/l amount of 1,2-dichloroethene 0.2 µg/l trichloroethylene 0.1 µg/l sum of 11 chlorinated hydrocarbons 1.1 µg/l tetrachloroethene 0.1 µg/l Sum of trichloroethylene and tetrachloroethylene 0.2 µg/l sum 5 chlorinated ethylenes 0.5 µg/l 1,2-dichloropropane 1 µg/l 1,3-dichloropropane 1 µg/l 2,2-dichloropropane 1 µg/l 1,2,3-trichloropropane 1 µg/l 1,2-dibromo-3-chloropropane 1 µg/l 1,1-dichloro-1-propene 1 µg/l cis-1,3-dichloro-1-propene 1 µg/l trans-1,3-dichloropropene 1 µg/l hexachlorobutadiene 1 µg/l 2-chlorotoluene 1 µg/l 4-chlorotoluene 1 µg/l monochlorobenzene 0.1 µg/l bromobenzene 1 µg/l 1,2-dichlorobenzene 0.1 µg/l 1,3-dichlorobenzene 0.1 µg/l 1,4-dichlorobenzene 0.1 µg/l amount of 3 dichlorobenzene 0.3 µg/l 1,2,3-trichlorobenzene 0.1 µg/l 1,2,4- trichlorobenzene 0.1 µg/l 1,3,5-trichlorobenzene 0.1 µg/l amount of 3 trichlorobenzene 0.4 µg/l benzene 0.1 µg/l toluene 0.5 µg/l ethylbenzene 0.1 µg/l o-xylene 0.1 µg/l m/p-xylene 0.2 µg/l sum of xylenes 0.3 µg/l summa BTEX 1 µg/l board one 0.2 µg/l isopropylbenzene 1 µg/l n-propylbenzene 1 µg/l 1,2,4-trimethylbenzene 1 µg/l 1,3,5-trimethylbenzene 1 µg/l n-butylbenzene 1 µg/l sec-butylbenzene 1 µg/l tert-butylbenzene 1 µg/l p-isopropyltoluene 1 µg/l naphthalene 1 µg/l Diisopropyl ether (DIPE) 0.6 µg/l ETBE (ethyl tert-butyl ether) 0.2 µg/l MTBE (methyl tert-butyl ether) 0.2 µg/l tert-amyl ethyl ether (TAEE) 0.2 µg/l TAME 0.2 µg/l tert-butyl alcohol (TBA) 5 µg/l ethanol 100 µg/l A customized offer can also be prepared if you are interested in analyzing only individual compounds from a sample. Suitable sample containers for analysis can be ordered through us. Sample containers picked up from Measurlabs are included in the price of the analysis, but sample containers can also be shipped to the customer for a separate fee.

We offer two methods for determining the total fluorine (TF) content of combustible materials: Accredited EN 14582 method, based on combustion ion chromatography (CIC). This is the default approach, recommended by the Nordic Council of Ministers as a quick and powerful total fluorine screening technique., EN 15408 mod. method using oxygen bomb combustion treatment followed by ion chromatography (IC). This method can be applied to plastic sheets and granules, and it is also possible to determine the total content of S, Cl, and Br. Please let us know if you wish to use this method.. The displayed starting price includes an analysis according to EN 14582, with sample preparation (air drying and milling of the sample to particles smaller than 1 mm) included.

Determination of bromide, fluoride, chloride, nitrate, nitrite, and sulfate (Br-, F-, Cl-, NO2-, NO3- ja SO42-) in soil, sludge, sediment, and water samples with ion chromatography. For soil, sludge, and sediment, the analysis is carried out after a water extraction. Ask about the price for other solid matrices and more challenging aqueous matrices. Please store the samples in refrigerated conditions and in gas-sealed containers.

GC-MS analysis of 16 PAH compounds, which are listed as high-priority pollutants by the U.S. Environmental Protection Agency (EPA). The analyzed PAH compounds are: naphthalene [CAS: 91-20-3], acenaphthylene [CAS: 208-96-8], acenaphthene [CAS: 83-32-9], fluorene [CAS: 86-73-7], phenanthrene [CAS: 85-01-8], anthracene [CAS: 120-12-7], fluoranthene [CAS: 206-44-0], pyrene [CAS: 129-00-0], benz(a)anthracene [CAS: 56-55-3], chrysene [CAS: 218-01-9], benzo(b)fluoranthene [CAS: 205-99-2], benzo(k)fluoranthene [CAS: 207-08-9], benzo (a) pyrene [CAS: 50-32-8], dibenzo(ah)anthracene [CAS: 53-70-3], benzo (ghi) perylene [CAS: 191-24-2], indeno (123cd) pyrene [CAS: 193-39-5].

With this analysis, the volatile organic compounds (VOC) present in a biogas sample can be quantified. Typically, the boiling range of the detected VOCs is 60-280 °C. Samples are collected using a pump and an adsorbent tube. The analysis employs a GC-MS method and utilizes external standard materials and mass-spectrum libraries to identify and quantify the compounds. Samples to be delivered in gas sampling bags (2 liters in volume). The cylinder gas samples will include additional logistics fees.

Raman spectroscopy is a non-destructive chemical analysis technique used for the identification of chemical components in a sample. This analysis is suitable for inorganic and organic liquid samples.