Direct peptide reactivity assay (DPRA) according to OECD 442C

Assessment of skin sensitization potential using the ARE-Nrf2 luciferase test method outlined in OECD Test Guideline 442D and listed in Annex C of ISO 10993-10 as an in-vitro alternative to traditional in vivo sensitization tests. The method has been validated for medical device extracts. The assay models the keratinocyte activation pathway — key event 2 in the skin sensitization adverse outcome pathway (AOP) as described by the OECD. Human keratinocytes are exposed to the test substance at a range of concentrations. If the substance has skin sensitization potential, it activates the Nrf2 transcription factor, which binds to the antioxidant response element (ARE) and induces luciferase expression. The measured luciferase activity thus correlates with the sensitization potential of the substance. According to Annex C of ISO 10993-10, a substance is classified as a skin sensitizer if luciferase activity increases by 50% relative to the solvent control at a concentration where cell viability is not significantly reduced. Two extracts (one polar and one non-polar) are prepared per tested device, and testing is performed in duplicate for each solvent.

We offer comprehensive test packages for verifying the quality of type II and type IIR face masks according to the EN 14683 standard. The tests included in the packages are required to label face masks with the CE marking. Medical face masks are divided into Types I and II according to their bacterial filtration efficiency. Type I masks are not intended for healthcare professionals, but for the public to prevent the spread of infectious diseases. Type II masks are further classified based on whether they are splash-resistant (Type IIR) or not (Type II). To comply with the European Standard EN 14683, Type II face masks must undergo the following quality tests: Bacterial filtration efficiency (BFE) - The ability of the face mask to filter the bacterium Staphylococcus aureus. The BFE is expressed as the percentage of colony-forming units (cfu) that have passed via aerosol through the facemask. If a face mask consists of two or more areas with different characteristics, these areas will be tested separately., Breathability (Differential pressure) - The amount of differential pressure required to draw air through a measured surface area at a constant flow rate., Microbial cleanliness (Bioburden) - The measurement of colony forming units per gram as per EN ISO 11737-1., Biocompatibility - The medical face mask manufacturer shall complete a biocompatibility evaluation according to ISO 10993-1 as a surface device with limited contact. The applicable toxicology testing regimen shall also be determined.. In addition to the above, Type IIR masks require the following test: Splash resistance - Performed according to ISO 22609, this test determines the ability of a face mask to resist penetration of splashes of liquid at different pressures.. The lower displayed price applies to the Type II mask test package, while the higher price also includes the splash resistance test required for Type IIR masks.

Sensitization assessment according to ISO 10993-10 is a crucial part of biocompatibility testing and one of the most common tests required to ensure the safety and compliance of medical devices. The goal is to show that the device does not cause skin sensitization, such as allergic responses or immunological reactions, when in contact with the body. A sensitization assessment is required for new medical devices to be approved in the EU (under the MDR) and the USA (510(k) submission to the FDA). Sensitization tests can be performed on the material or device itself, or an extract, depending on the device and test method type. ISO 10993-10 lists several in vitro and in vivo assays to assess the sensitization potential of medical devices and chemicals extracted from them. In vitro assays evaluate skin sensitization potential by detecting chemical reactions or cell responses to the chemicals. Conversely, in vivo assays expose animals to the test sample or extract, which is typically applied in induction and challenge phases. Sensitization potential is then evaluated by observing possible reactions to the exposure. The sensitization reaction to the medical device is scored based on the evaluation criteria defined in ISO 10993-10. We can provide sensitization tests using several methods. A few examples are outlined below. In vivo methods: Guinea pig maximization test (GPMT), Closed-patch test (Buehler), Murine local lymph node assay (LLNA). In vitro methods: ARE-Nrf2 Luciferase test, Direct peptide reactivity assay (DPRA). The displayed example price covers testing with the commonly used GPMT method for liquid medical devices, performed under GLP. Please ask for a quote for your medical device.

The purpose of cleaning validation studies is to show that reusable medical devices can be reprocessed effectively between uses so that patients are not exposed to pathogens. Depending on the device’s intended use and classification, appropriate reprocessing steps may include cleaning, disinfection, and/or sterilization. For cleaning validation more specifically, the testing procedure consists of three steps: Simulated contamination with artificial soils that accurately reflect clinically relevant soils, such as blood and other bodily fluids. , Cleaning (manual and/or automated), carefully following the manufacturer's instructions for parameters such as detergents, cleaning tools, water quality, and temperature. , Inspection, both visually and using quantitative methods relevant to the test soil (e.g., proteins, total organic carbon, or hemoglobin), to assess whether residual contaminants remain on the device.. Successful cleaning validation is often sufficient for non-critical reusable devices, such as blood pressure cuffs, monitors, and clutches. Semi-critical and critical devices will require further disinfection and/or sterilization validation studies, which we can also offer. The displayed example price covers a manual cleaning validation study with 6 reprocessing cycles and cleanability evaluations with visual inspection & protein content measurement. Test protocol formulation and reporting are also included.

ISO 10993-23 is an internationally recognized standard for assessing the irritation potential of medical devices when they come into contact with skin, mucosal membranes, or subcutaneous tissues. Irritation tests performed according to the standard are commonly used to demonstrate compliance with EU MDR and FDA requirements. The appropriate testing approach is chosen based on the body contact site: Skin irritation tests evaluate whether a medical device or material causes localized skin irritation when it comes into direct contact with the skin. Testing can be conducted using in vivo or in vitro methods, depending on the device and the market area. , Intracutaneous reactivity tests apply to medical devices or materials that penetrate the skin or come into contact with deeper tissues. The goal is to determine whether extracts from such devices cause localized inflammatory responses in the dermis or subcutaneous layers.. The device itself is tested with a direct contact method, when possible. Alternatively, polar and non-polar solvents are used to prepare extracts that simulate potential leachables from the device. The displayed example price includes an in vivo direct skin irritation test performed under GLP. For a more accurate quote, do not hesitate to contact us with a description of your device and any additional requirements you may have for testing (e.g., market area, quality systems, in vivo vs. in vitro methods).

The biocompatibility of medical devices with breathing gas pathways is generally assessed according to ISO 18562 standards. Measurlabs offers tests according to this standard family, including the following: ISO 18562-2: Tests for emissions of particulate matter (PM), ISO 18562-3: Tests for emissions of volatile organic substances (VOS), ISO 18562-4: Tests for condensate volume and leachables from condensate. Our experts are happy to help with any questions related to the tests and prepare a quote for you. Describe your testing needs using the form below, and we will get back to you shortly.

The bacterial reverse mutation (AMES) test is used to evaluate the genotoxic effect of a medical device or its extract when in contact with a bacterial suspension. The test is conducted according to OECD 471 and ISO 10993-3 by exposing a bacterial suspension of Salmonella spp and Escherichia coli to 5 concentrations of the medical device or its pure extracts. The AMES test is a preliminary "screening test" for genotoxicity. A full genotoxicity evaluation usually includes testing the device with two in vitro methods, of which AMES is typically performed first. An additional in vivo method can be used if needed. Measurlabs can support you with the full genotoxicity evaluation. Please contact our experts for a quote.

Pyrogenicity assessment by ISO 10993-11 to evaluate the material-mediated pyrogenic (i.e., fever-inducing) potential of medical devices. Material-mediated pyrogenicity tests focus on non-endotoxin-related substances, including bacterial exotoxins, endogenous pyrogens, prostaglandin, neurotransmitters, and metal salts. These can be studied using in vitro assays, where the fever-inducing potential is evaluated using cells, or in vivo rabbit pyrogen tests, where the animal's body temperature is monitored upon exposure to device extracts. Measurlabs provides testing using the following methods: Material-mediated pyrogenicity - In vivo (rabbit), Material-mediated pyrogenicity - In vitro (MAT, Monocyte Activation Test). Please ask for a quote for your medical device. We also offer Bacterial endotoxin tests (ISO 11737-3) to evaluate endotoxin-related pyrogenicity.

In vitro identification of chemicals not requiring classification for eye irritation or serious eye damage, using the EpiOcular™ Eye Irritation Test (EIT) according to OECD Test Guideline 492. The method uses a reconstructed human cornea-like epithelium (RhCE) tissue construct that closely mimics the histological and physiological properties of the human corneal epithelium, and serves as a non-animal alternative to the in vivo rabbit eye test (OECD 405). The test substance is applied topically to the RhCE tissue. Following exposure and a post-treatment incubation period, tissue viability is measured by the MTT assay and expressed as a percentage of the negative control. A substance is identified as not requiring classification (UN GHS No Category) if tissue viability exceeds 60%. Substances that reduce viability below this threshold are considered to require classification, but the method cannot differentiate between UN GHS Category 1 (serious eye damage) and Category 2 (eye irritation) — further testing is required to make that distinction. OECD TG 492 is accepted for eye irritation and serious eye damage hazard assessment under REACH (Annex VII/VIII information requirements) and the EU Biocidal Products Regulation (Regulation (EU) No 528/2012, Annex II core data set). It is also mentioned alongside other in vitro OECD methods in the latest version of ISO 10993-23 standard on medical device irritation tests, although it is noted that several in vitro tests in a tiered testing strategy may be needed to replace the in vivo OECD 405 test.

The NRU assay is a quantitative test to determine the potential biological reactivity of a mammalian cell culture in response to a medical device extract. It is described in Annex A of ISO 10993-5 and is one of the most commonly used methods for medical device cytotoxicity testing. The test item is extracted in cell culture medium, which is suitable for both polar and non-polar extracts. The cells are exposed to the extract, and their viability is assessed after staining with neutral red (NR) solution. The number of viable cells correlates with the color intensity determined by photometric measurements, as non-viable cells do not absorb NR. The medical device is considered non-cytotoxic if the percentage of viable cells is ≥ 70 % of the untreated control.