Water vapor transmission rate (WVTR) of textiles

Determination of the water vapor transmission rate (WVTR) of ultra-high barrier materials. The method can also be used to test moderate barrier materials at high-temperature conditions. Please disclose the desired temperature (from 10 to 85 °C) and the desired relative humidity (from 60% to 100%) when placing the order. This measurement is applicable for films and sheeting materials with WVTR values between 1x10-6 and 10 g/m2/day. If you wish to test finished packaging instead, check out the WVTR measurement for packages. The price of the test consists of a flat rate cost per sample plus one day measurement time. Please contact our experts for an offer.

The gravimetric dish method can be used to determine the water vapor transmission rate (WVTR) of materials that have a high water vapor permeability. This method is intended for plastic films or sheeting materials with a water transmission rate of over 1 g/m²/day. The maximum sample thickness is 3 mm. In the test, a water-absorbent material is placed in a metal cup that is covered by the studied material, which is sealed to the cup with wax. The test sample is placed in a conditioned cabinet and its mass is measured. From this, the WVTR value can be calculated. The method is not applicable for materials that are damaged by hot wax or shrink under the used test conditions.

Determination of the water vapor transmission rate (WVTR) according to the ASTM F1249 standard. WVTR describes the amount of water vapor that passes through a material over a set period. It is an important quality indicator in food and cosmetics packaging, as an effective moisture barrier is critical to keeping products fresh and preventing spoilage. In this WVTR test, two samples per material are measured simultaneously to ensure the reliability of the measurement. The results are expressed as g/m²/day. Please disclose the desired temperature (from 18 to 40°C) and the desired relative humidity (from 20% to 100%) when placing the order. This measurement is applicable for plastic films and sheeting materials with WVTR values between 0.005 and 2400 g/m²/day. If you wish to test finished packaging instead, check out the WVTR measurement for packages.

This test is designed to measure the oxygen transmission rate of finished packages, including cups, bottles, trays, and containers. Two replica measurements are included in the displayed price. Temperature can be adjusted from 15 to 55 °C, and relative humidity can be either 0% or between 5 and 90% RH. This test is not suitable for films. Please see the oxygen transmission rate (OTR) of films and sheeting if you need testing for film samples. Please specify the sample dimensions and testing conditions upon ordering.

Phthalates are a group of chemicals widely used as plasticizers, which make plastics more flexible and durable. They have also been used as additives in products such as cosmetics and personal care items. Several phthalates have been identified as endocrine-disrupting agents or as chemicals toxic to reproduction. Exposure to phthalates can occur through: Oral exposure Food: Exposure occurs via migration from food packaging., Children's toys: Children often put toys in their mouths.., Inhalation: Breathing in dust from vinyl flooring or fragrances (like perfumes) can cause exposure to phthalates via inhalation., Skin contact: Phthalates present in cosmetics, lotions, and soaps can be absorbed through the skin.. For other listed matrices apart from cosmetics, the analysis package covers the following substances included in the REACH Authorization List: Substance Abbreviation CAS number Diisobutyl phthalate DIBP 84-69-5 Dibutyl phthalate DBP 84-74-2 Benzyl butyl phthalate BBP 85-68-7 Bis(2-ethylhexyl) phthalate DEHP 117-81-7 Di(n-octyl) phthalate DNOP 117-84-0 Diisononyl phthalate DINP 68515-48-0 Diisodecyl phthalate DIDP 26761-40-0 Products that contain restricted phthalates in concentrations higher than 0.1% may be removed from the market. The analysis package for cosmetic products contains the following phthalates: Substance Abbreviation CAS number Bis(2-ethylhexyl) phthalate DEHP 117-81-7 Benzyl butyl phthalate BBP 85-68-7 Dibutyl phthalate DBP 84-74-2 Diisononyl phthalate DINP 68515-48-0 Di(n-octyl) phthalate DNOP 117-84-0 Diisodecyl phthalate DIDP 26761-40-0 All the above-mentioned substances are prohibited in cosmetic products (Annex II of Regulation (EC) No 1223/2009).

Determination of the oxygen transmission rate of plastic films and sheet-like materials. The test is performed on two parallel samples simultaneously. Measurement conditions (temperature and relative humidity) can be chosen according to the intended use of the material. Oxygen permeability is typically measured at 23 °C and 0% relative humidity as per standard ASTM D3985. In moist conditions, for example at 38 °C and 90% relative humidity, standard ASTM F1927 is used. Please disclose the desired temperature (from 10 °C to 38 °C) and relative humidity (either 0% or from 20% to 90%) upon ordering. This measurement is suitable for plastic films with OTR values between 0.05 to 20 000 cm³/(m² * day).

This measurement determines the transmission rate of carbon dioxide (CO2) through a single or multi-layered plastic film or sheeting with an infrared detector. The measurement is performed with two parallel specimens. The testing temperature is 23°C, and the relative humidity is 0%.

Imaging of the sample using scanning electron microscopy (SEM). Typically, several images are taken with varying magnifications to get a good overview of the sample. Non-conductive samples can be prepared with a metallic coating to allow imaging. For cross-section measurement, additional preparation might be needed: FIB, BIB or freeze fracturing. If compositional analysis is also needed, please see the SEM-EDX measurement.

Analysis for quantifying dioxins and furans (PCDD/F) in various packaging materials (e.g. food and cosmetics packaging) and their raw materials, including plastics, paper, and rubber. Dioxins and furans are a family of chlorine-containing chemicals considered bioaccumulating, persistent organic pollutants (POPs) that can be toxic even at low doses. While regulatory limits apply mainly to food and feed, packaging materials can be a source of indirect exposure to dioxins and furans. Recycled materials tend to pose relatively high risks, depending on the quality of the raw material and the effectiveness of the decontamination process. The following substances are included in the analysis: Dibenzo-p-dioxins (PCDDs) Polychlorinated dibenzofurans (PCDFs) 2,3,7,8-TCDD. 2,3,7,8-TCDF. 1,2,3,7,8-PeCDD. 1,2,3,7,8-PeCDF. 1,2,3,4,7,8-HxCDD. 2,3,4,7,8-PeCDF. 1,2,3,6,7,8-HxCDD. 1,2,3,4,7,8-HxCDF. 1,2,3,7,8,9-HxCDD. 1,2,3,6,7,8-HxCDF. 1,2,3,4,6,7,8-HpCDD. 1,2,3,7,8,9-HxCDF. OCDD. 2,3,4,6,7,8-HxCDF. 1,2,3,4,6,7,8-HpCDF. 1,2,3,4,7,8,9-HpCDF. OCDF. Testing is often performed for the following reasons: Analyzing recycled PE, PP, and LDPE intended for cosmetics packaging according to CosPaTox guidelines., Analyzing paper and board bleached with elementary chlorine according to the requirements of TemaNord 2008:515 guidelines..

Determination of the total organic fluorine (TOF) content in combustible materials by combustion ion chromatography (CIC). TOF analysis gives information about the total amount of organic fluorinated compounds. It can also be used to evaluate the presence of per- and polyfluoroalkyl substances (PFAS) in the material, even though individual PFAS compounds can't be analyzed with this method. The analysis is suitable for many different materials. Please describe the sample in detail when requesting an offer to help us prepare a quote quickly.